Adding an extra fuel injector

Take a look underhood of Clifford:

Look close and you'll see quite a few things which weren't put there by the factory. My latest additions are the 5th injector and the pressure switch which controls it. While Gus had a page on adding an extra injector and Gary Donovan has one as well, their pages don't quite tell the whole story. Indeed, I had a few small but important questions about the procedure and I did lots of asking before proceding with the operation. Now that the job is complete and functional I want to share the how-to with all my internet friends. Here's a rundown.

WARNING! Since performing this injector installation, I have learned that teflon tape should not be used with gasoline. The gas will eat away at the tape and will probably end up leaking. I say probably because my setup never actually leaked; perhaps the brass fittings snugged all the way into the tee? I guess I just lucked out. At any rate, do not use teflon tape--use a liquid pipe thread sealer approved for use with gasoline.

In your metal intercooler pipe, drill a hole which is barely larger than the injector's nozzle--six inches in front of the throttle body is ideal. Temporarily put the injector in place, use its flange to mark where the screw holes go, then remove the injector and drill those holes. Once the holes are ready and the pipe has been thoroughly cleaned of metal shavings, place a half-inch piece of 5/16" fuel hose over the tip of the injector and install it permanently--the small piece of hose will compress and conform to the shape of the pipe making an airtight seal. Sheet metal screws will do the job perfectly; I even went so far as to add a very small dab of RTV for these screws to ensure a good seal but this is overkill so long as you don't drill holes which are too big for the screws. Now that the injector is mounted, plumb in the fuel hose from the 3/16" barb of the brass tee.

You need to mount a pressure switch to control the injector. (Go to NAPA and ask for NAPA part# 7011577. This corresponds to a hobbs pressure switch #76052 which is a single circut 5000 series normally open 2 terminal switch. It is factory set to 15 psi but adjustable 14-24 psi. NOTE: the switch pictured above is not the NAPA switch--it's what I had lying around.) I decided to tee into the line for the fuel pressure regulator; I felt this was safe since there will be no bleed-off of pressure. Feel free to mount your switch wherever you like.

Speaking of pneumatics, you don't install an extra injector unless you're going to run more than 14 psi of boost. And if you're going over 14 pounds then you'll also need to trick the MAP sensor. My solution was to install a cutout raiser as Gus describes on his web page. I did make one deviation, though: rather than epoxy a plastic tee onto the valve I bought a brass barb which screws onto the valve. This way I'd have no chance of messing up the machined seat for the brass ball inside the valve. See the difference in the pictures below--Gus shows his way on the left while my method is on the right.

Part III: wiring it all in

Now all you need to do is wire everything together. The injector has two wires and polarity does not matter--feed 12v to one and ground to the other and you'll get fuel. I attached one wire to a constant 12v source; this line contains a 1-amp inline fuse for safety. I then connected the other injector wire to one of the terminals of the pressure switch. The switch's second terminal is connected to ground. When the threshold pressure is reached the switch closes and sends ground to the injector, turning it on. Once pressure falls below the threshold, the switch opens and the injector shuts off.

For neatness sake, I used as much of the injector's wiring as I could. When you remove a cold start injector from a junkyard car try to cut off as much of the harness as you can--you'll appreciate it later.

Now all that's left is making it all work. Gradually raise your boost level one pound at a time; make sure your fuel gauge says all is well. If you hit cutout adjust your raiser very slightly and try again. After a bit of experimentation you should get dialed in to your target boost setup. Once you do, be sure to read your sparkplugs to confirm everything is okay. If it is, you're all set!